![]() ![]() On the shortcut menu, click Properties, and on the Tools tab in the Properties dialog box, click Check Now in the Error-Checking Status area. ĭouble-click My Computer, and right-click the hard disk. Use the Error Checking utility built in to Microsoft Windows. For example, Windows Disk Error Checking can help to fix corrupted file system structures. Nonetheless, if the drive passes all of the SeaTools hardware tests and you still have concerns that the disk drive is the cause of problems, then you may need to perform other tests and maintenance. This way, the benefits of the long scan are enjoyed without the long duration of the whole drive scan. If found, these sectors are considered questionable and they are the first ones tested by the DST short test. While both versions can initiate the drive's built in self test (called DST), the bootable version, SeaTools for DOS, has additional capabilities if bad sectors are found.Īn interesting aspect of disk drive technology is that since early 2000 disk drives are constantly using idle time to scan for difficult sectors. There are two versions of SeaTools, one runs in Windows and the other runs from its own bootable operating system on a CD or floppy. That means a significant number of customers who were returning their good disk drives were forfeiting valuable data and productivity. Prior to the availability of SeaTools, many of the hard drives returned to Seagate were found to have no problems. ![]() ![]() Additionally, removing your drive will reduce your productivity until it is replaced. It is important that you not risk losing all your data by returning a perfectly good disk drive. If it passes all tests, then the problem is usually located somewhere else in your system. I read (but didn't save the link) that it doesn't bother trying to repair more than a 1000 of them because we should get a new HDD after that point anyway.SeaTools thoroughly tests your Seagate, Maxtor-brand, and Quantum-brand ATA drives. SeaTools suggested I could use a DOS version to repair broken sectors, burn a CD but it wasn't able to repair them. I'm impressed I have two identical models that are giving different error messages. I was able to install Ubuntu on a third drive (Seagate Barracuda ST3160815AS 160GB) and boot into it. How can I regain access to the drives to keep going on this joyous quest of failing to install Ubuntu? I have attempted to switch the computer to use AHCI on a hunch that it might make it easier to detect the drives (which it didn't.) Question Fails at 25% with The ext4 file system creation in partition#1 of SCSI2 (0,0,0) (sda) failed. The machine seem think that Ubunut was already installed (after the initial botched installation). At about 75% of copying files it errored saying it couldn't copy a file and that it could be because the drive was faulty. Then attempted to install getting past the partition screen and into localization setup. I formatted the drive with 480GB EXT4 and 20GB linux-swap successfully. S.M.A.R.T was saying it has 2700 faulty sectors, which seemed a bit excessive and thought it might be confused. It had a 50gb unknown block (and the rest was free I think). Once I managed to get past it being stuck (by specifying gparted /dev/sda). When I looked at it having booted in with a live CD and tried to look at the disk in GParted it would get stuck at "scanning for devices". Wouldn't make it to the partition part of the installation instead it would be stuck at loading (as indicated by mouse cursor), using administrative tools still worked so it wasn't simply hung. After rebooting it was still detectable on the same machine. Putting the disk in one of the other machines (different hardware) gave the same input/output error during read /dev/sda. I put the jumper back in place, without any effect The drive is now undetected even in BIOS. Before clicking next I ran fdisk -l upon which it spewed out a bunch of error messages (can't remember what they said off-hand), it then ended up erroring with a input/output error message when I clicked next. I made it to the partition screen where I set it to have a 480GB EXT4 with a 20GB linux-swap. Wouldn't at first get detected in Ubuntu until I removed the jumper that was putting it in 1.5gb legacy mode. At the start I was using a DVD with Ubuntu, at the end I'm using a USB stick (as I thought perhaps the DVD was at fault.) Both the drives are Seagate Barracuda 500GB ST3500320AS. I've detailed below the process I've gone through in case it lends anyone a clue. Both the 500GB drives has now become undetectable and don't even show up in BIOS. I've been trying to setup Ubuntu but have been running into countless issues. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |